Laboratory Ovens Australia
France Etuves Universal Oven XUE Series
Laboratory Ovens for Many Processes.
Temperature: max. 300°C
The FRANCE ETUVES XUE lab drying oven is suitable for drying, heating, heat preservation, sterilization, component aging, curing or any other thermal test in laboratories and in all sectors of industry.
This quality lab drying oven comes in 8 standard volumes : 32, 58, 112, 225, 343, 490, 686 and 980 liters.
The oven is equipped with an internal light activated by a switch located on the control panel.
The rounded corners of the inner casing make easier cleaning operations.
Robust manufacturing that meets lab drying oven quality requirements.
The outer plates of the oven are made of electro galvanized steel coated with white and blue paints.
The inner casing is made of bright polished stainless steel. Stainless steel is particularly corrosion resistant, allowing you to process higher water content products.
The control panel is located on the top part of the oven for smallest space requirements.
ENTRY PORT 20 mm
An entry port is centered on the left side for passing cables or probes. A silicone cork allows you to block the entry port in case of non-use or to make airtight after passing cables.
An exceptionally effective universal drying oven.
The thermal insulation by asbestos-free glass wool is optimized.
The outer casing is separated from the inner casing. There is no thermal bridge in order to ensure :
– low surface temperatures,
– low power consumption,
– rapid heating up.
Air tightness of the door is ensured by a long-lasting stabilized silicone seal. It is easily removable for an easy and quick cleaning.
AN EFFICIENT HEATING
Heating is ensured by sheathed stainless steel heating elements, ideally positioned in the air flow, allowing homogeneous heating up.
A forced convection for an amazing temperature homogeneity!
Ventilation is provided by one or two fan(s) motor.
It speeds up the drying process and homogenizes heating in the working volume. Inside the oven, air is sucked by the fan (1).
It is heated by the heating elements (2), then is blown into the working volume (3). The hot air goes out through at the back of the oven (4). Fresh air enters the volume near the fan (5).
Adjustable air change
It is possible to create an air change inside the working volume. Thanks to an adjustment button, open more or less the flap of the air outlet located at the backside of the oven. Hot air escapes from the air outlet and is replaced by ambient air.
The C3030 Temperature Controller/Profiler
The FRANCE-ETUVES C3030 temperature controller is very accurate and particularly reliable.
Measurement by PT100 or TCJ probe. Electronic PID temperature controller. Accuracy: 0.1°C.
Color display, excellent visibility of temperatures.
– display of setpoint and measured temperature
– display (in percentage) of the heating power used
– date and time display
– Possibility of making 1 program with 8 steps: 4 programmable temperature ramps (°C/min) and 4 heating timer (max 9999min)
– delayed start
– repeat loop
– monitoring of your current program (step and remaining time)
– pause or stop the program
– end of cycle buzzer
– fan speed control
– several settings of the protection thermostat (TWW or TWB modes)
– PID adjustment
– possibility of adding a temperature correction at 2 distinct temperatures (offsets)
– automatic fault diagnosis. Display of faults
– RS485 modbus multipoint communication: allows to control several ovens on the same network
C3030 Temperature Controller for XUE Series
(C3000 also available for XU Series)
Choose from the following XUE Lab Drying Oven Models…
XUE032 Laboratory Oven
XUE058 Laboratory Oven
XUE112 Laboratory Oven
XUE225 Laboratory Oven
XUE343 Laboratory Oven
XUE490 Laboratory Oven
XUE686 Laboratory Oven
XUE980 Laboratory Oven
Unrivaled Quality… Order the Most Proven Laboratory Oven Today
+61 3 9404 2610
Premium Customer Support | Australia-wide Delivery